Tic T500 USB步進馬達控制板

MOM0081

Tic T500 USB多界面步進電機控制器使得我們的免費軟件能夠通過USB進行快速配置,從而簡化了步進電機的基本控制。 該控制器支持六個控制接口:USB,TTL串行,I²C,模擬電壓(電位計),正交編碼器和業餘無線電控制(RC)。 該版本包含一個MPS MP6500驅動器,並且包含公頭和端子塊,但未焊接。 它可以在4.5 V至35 V的電壓下工作,並且每相可以提供高達約1.5 A的電流,而無需散熱器或強制空氣流(最大2.5 A,額外冷卻)。

更多資訊

NT$ 788 含稅

-NT$ 63

NT$ 850 含稅

更多資訊

產品簡介

The Tic family of stepper motor controllers makes it easy to add basic control of a bipolar stepper motor to a variety of projects. These versatile, general-purpose modules support six different control interfaces: USB for direct connection to a computer, TTL serial and I²C for use with a microcontroller, RC hobby servo pulses for use in an RC system, analog voltages for use with a potentiometer or analog joystick, and quadrature encoder for use with a rotary encoder dial. They also offer many settings that can be configured using our free configuration utility (for Windows, Linux, and macOS). This software simplifies initial setup of the device and allows for in-system testing and monitoring of the controller via USB (a micro-B USB cable is required to connect the Tic to a computer).

產品規格

Dimensions

Size: 1.50″ × 1.05″ × 0.47″
Weight: 8.2 g

General specifications

Model: Tic T500
Motor driver: MP6500
Control interface: USB; non-inverted TTL serial; I²C;
RC servo pulses; analog voltage; quadrature encoder
Minimum operating voltage: 4.5 V1
Maximum operating voltage: 35 V
Continuous current per phase: 1.5 A2
Maximum current per phase: 2.5 A3
Maximum step rate: 50000 PPS
Microstep resolutions: full, 1/2, 1/4, and 1/8
Reverse voltage protection?: Y
Connectors soldered: Y

Identifying markings

PCB dev codes: tic03a
Other PCB markings: 0J11038

Notes:

  • Powering the Tic T500 with a supply voltage between 4.5 V and 5.5 V might cause its logic voltage to be lower than normal, which could affect operation. See the user’s guide for more information.
  • Without a heat sink or forced air flow.
  • With sufficient additional cooling.

文件下載

Tic Software and Drivers for Windows (9MB msi)
Tic Software for Linux (x86) (8MB xz)
Tic Software for Linux (Raspberry Pi) (6MB xz)
Tic Software for macOS (7MB pkg)
Dimension diagram of the Tic T825 USB Multi-Interface Stepper Motor Controller (199k pdf)
Dimension diagram of the Tic T834 USB Multi-Interface Stepper Motor Controller (215k pdf)
Dimension diagram of the Tic T500 USB Multi-Interface Stepper Motor Controller (295k pdf)
Texas Instruments DRV8825 stepper motor driver datasheet (1MB pdf)
Texas Instruments DRV8834 stepper motor driver datasheet (2MB pdf)
MPS MP6500 stepper motor driver datasheet (1MB pdf)
3D model of the Tic T825 USB Multi-Interface Stepper Motor Controller (12MB step)
3D model of the Tic T834 USB Multi-Interface Stepper Motor Controller (11MB step)
3D model of the Tic T500 USB Multi-Interface Stepper Motor Controller (11MB step)
Drill guide for the Tic T825 USB Multi-Interface Stepper Motor Controller (76k dxf)
This DXF drawing shows the locations of all of the board’s holes.
Drill guide for the Tic T834 USB Multi-Interface Stepper Motor Controller (71k dxf)
This DXF drawing shows the locations of all of the board’s holes.
Drill guide for the Tic T500 USB Multi-Interface Stepper Motor Controller (82k dxf)
This DXF drawing shows the locations of all of the board’s holes.
UM10204 I²C-bus specification and user manual (1MB pdf)
The official specification for the I²C-bus, which is maintained by NXP.