Hi-Res Display for Raspberry Pi (非觸碰式)

VED0062

高分辨率、高速、4.0英寸顯示器,帶可選的觸控螢幕,適用於Raspberry Pi

HyperPixel 4.0 Square具有我們標準HyperPixel 4.0的所有強大功能-清晰、明亮的IPS顯示螢幕,可選的觸控螢幕和高速DPI界面

加購樹莓派:

4GB 8GB

更多資訊

NT$ 2,499 含稅

更多資訊

【產品簡介】

高分辨率、高速、4.0英寸顯示器,帶可選的觸控螢幕,適用於Raspberry Pi

HyperPixel 4.0 Square具有我們標準HyperPixel 4.0的所有強大功能-清晰、明亮的IPS顯示螢幕,可選的觸控螢幕和高速DPI界面

此版本的HyperPixel 4.0可用於自定義介面和控制面板,對於Pico-8遊戲的呈現效果非常棒 !

不需額外焊接腳位,只需將專案匯入到您的Pi上,運行我們的安裝程序,就可以了!

----------------------------------------------------------

【產品特色】

  • High-speed DPI interface
  • 4.0" IPS (wide viewing angle, 160°) display (72x72mm)
  • 720x720 pixels (~254 PPI)
  • 18-bit colour (262,144 colours)
  • 60 FPS frame rate
  • Optional capacitive touchscreen
  • 40-pin female header included to boost height for Pi B+、2、3、3B+ and 4
  • Standoffs included to securely attach to your Pi
  • Compatible with all 40-pin header Raspberry Pi models
  • One-line installer

HyperPixel 4.0 Square uses a high-speed DPI interface, allowing it to shift 5x more pixel data than the usual SPI interface that these small Pi displays normally use. It has a 60 FPS frame rate and a resolution of approximately 254 pixels per inch (720x720px) on its 4.0" display. The display can show 18-bits of colour (262,144 colours).

The touchscreen variant is capacitive touch, that's more sensitive and responsive to touch than a resistive touch display, and it's capable of multi-touch!

Please note: when installing HyperPixel 4.0 Square onto your Pi make sure not to press down on the screen surface! Hold the board by its edges and wiggle it to mate with the extended header (or GPIO header).  Also take care not to pull on the edges of the glass display when removing your HyperPixel.

It'll work with any 40-pin version of the Pi, including Pi Zero and Pi Zero W. If you're using it with a larger Pi then use the extra 40-pin header that's included to boost it up to the required height. If you're using a Pi Zero or Pi Zero W then just pop it straight onto the GPIO.

The included standoff kit allows you to mount your HyperPixel 4.0 Square safely and securely to your Pi. Just screw them into the posts on the underside of the HyperPixel 4.0 Square PCB and then secure with screws through the mounting holes on your Pi.

----------------------------------------------------------

【文件下載】

將安裝程序組合在一起,以針對HyperPixel 4.0 Square正確配置您的Pi並啟用觸控螢幕。請注意,您將需要另一個顯示器、鍵盤和滑鼠來安裝該軟體,或者,如果您按照指南進行設置,則可以通過SSH遠程進行安裝。

打開一個終端,然後鍵入  curl https://get.pimoroni.com/hyperpixel4 | bash 以運行單行安裝程序並設置HyperPixel 4.0。

在此處找到GitHub存儲庫:https :  //github.com/pimoroni/hyperpixel4

hyperpixel-square-redux-2_1024x1024__988hyperpixel-square-shop-2_1024x1024__9564hyperpixel-square-shop-3_1024x1024__0292hyperpixel-square-shop-4_1024x1024__3703

配件